Biostar P4VTB Manual do Utilizador

PPP444VVVTTTBBB i FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device

10 (7) Game Header: JGAME1 (does not support on version 7.x) 121615 JGAME1 Pin Assignment Pin Assignment 1 +5V 2 +5V 3 Joystick B Button 1 4

11 (9) Front USB Header: JUSB3/ JUSB4 Pin Assignment Pin Assignment 1 +5V 2 +5V 3 USBN- 4 USBN- 5 USB+ 6 USBP+ 7 Ground 8 Ground 21109 JUSB3/4

12 (12) Front Panel Audio Header: JAUDIO1 1213 14 JAUDIO1 Pin Assignment Pin Assignment 1 Mic In/ Center 2 Ground 3 Mic Power/ Bass 4 Audio

13 (14) Power Source Selection for USB: JUSBV1/ JUSBV2/ JUSBV3 (does not support on version 7.x) JUSBV1/JUSBV2/ JUSBV3 Assignment Description 1 3

14 ※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 close”. 3. Wait for five seconds. 4. S

15 (20) Consumer Infrared Header: J_CIR (only optional on version 7.x) Pin Assignment Pin Assignment 1 Ground 2 +5V Standby 3 CIRRX 4 CIRTX 5

16

17 Français Caractéristiques de P4VTB A. Matériel Processeur Avec socket 478. Prise en charge du processeur Intel® Pentium® 4. Prise en

18 Périphériques intégrés a. Côté arrière 2 ports série. (1 port série seulement pour version 7.x) 1 port parallèle (mode SPP/EPP/ECP) 1 port a

19 WarpSpeeder Introduction [ WarpSpeeder™ ], a new powerful control utility, features three user-friendly functions including Overclock Manager,

CCCooonnnttteeennntttsss ii Layout of P4VTB (only for version 1.x)...3 Layout of P4VTB (only for version 7.x)...

20 Installation 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default

21 Usage The following figures are just only for reference, the screen printed in this user manual will change according to your motherboard on h

22 This utility is responsible for conveniently invoking [WarpSpeeder™] Utility. You can use the mouse by clicking the left button in order to inv

23 3. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slid

24 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Pane

25 Overclock Panel contains these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”: provide user the ability

26 d. “Auto-overclock button”: User can click this button and [ WarpSpeeder™ ] will set the best and stable performance and

27 5. Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will

28 Note: Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [

29 Trouble Shooting PROBABLE CAUSE SOLUTION No power to the system at all; power light doesn’t illuminate; fan inside power supply does not turn

3 Layout of P4VTB (only for version 1.x) ※NOTE: ●represents the first pin.

30 PROBABLE CAUSE SOLUTION Screen goes blank periodically. * Disable screen saver. PROBABLE CAUSE SOLUTION Memory problem. * Reboot computer.

31 Dépannage PROBLÈME SOLUTION Pas d'alimentation au système. Les voyants lumineux ne s'allument pas, le ventilateur à l'intérieur

32 01/16/2004

4 Layout of P4VTB (only for version 7.x)

5 English 1. P4VTB Features A. Hardware CPU Provides Socket 478. Supports Intel® Pentium® 4 Processor. Supports Intel® Pentium® 4 Pre

6 On Board AC’97 Sound Codec (only for version 7.x) Chip: CMI9761A. Compliant with AC’97 specification. AC’97 2.2 interface. Supports 6 channe

7 3. How to setup Jumper The illustration shows how jumpers are setup. When the Jumper cap is placed on pins, the jumper is “close”. If no jump

8 CPU Fan Headers: JCFAN1 Pin No. Assignment 1 Ground 2 +12V 13 JCFAN1 3 FAN rpm Rate Sense System Fan Headers: JSFAN1 Pin No. Assignment 1 G

9 6. Jumpers, Headers, Connectors & Slots (1) Floppy Disk Connector: FDD1 The motherboard provides a standard floppy disk connector that sup